Nationally Accredited CertificationTraining and/or Assessment is available for the following National Occupational Health and Safety Commission (NOHSC)
Important note: Our Company does NOT have the machinery to conduct training or assessment upon. You must have access to the machinery (either through your workplace or your contacts) or be prepared to hire it. We have a location that can be used at Forest Hill (near Gatton). Tickets from Overseas cannot be ‘changed over’, the procedure below applies.
As of 1 July, 2007 the Queensland Government (WHSQ) changed the licensing system requirements.
-
You now have to prove that you have undergone a Training Course. Our Company can assist in providing a training course at your location or ours.
-
You need to enroll with a Registered Training Organisation (RTO). Our Company is an accredited RTO.
-
You have to prepare a Training Plan which outlines all the competencies required to be covered. Once you are enrolled with our Company you will be provided with an approved Training Plan.
-
You have to prove you have completed 40+ hours (see above tables for nominal hours) supervised operational experience by completing a Training Record Log Book which is signed off by a suitably ticketed supervisor. Once you are enrolled with our Company you will be provided with an approved Training Record Log Book.
-
Then you undergo a Written Assessment (which now requires a 100% pass rate) and a Practical Assessment. We can assist in providing suitable study information.
-
We send the Assessment Report and documentation to WHSQ along with the fee and WHSQ send you the ticket.
Delivery And Assessment Arrangements For
30496QLD Course In Operating Loadshifting Equipment |
Unit Code |
Unit Title |
RTO supervised training
(Nominal hrs) |
On-the-job training
(Nominal hrs) |
RTO supervised assessment
(Nominal hs) |
OHSCER202A |
Operate a front end loader/backhoe (LB) |
32-36 hours as a guide dependant on the experience and learning ability. |
40 hours |
4-8 hours as a guide |
OHSCER203A |
Operate a front end loader (LL) |
OHSCER204A |
Operate a front end loader (skid steer type) (LS) |
OHSCER205A |
Operate a excavator (LE) |
OHSCER207A |
Operate a fork lift truck (LF) * changing to TLILIC108A License to Operate a Forkilift Truck |
OHSCER209A |
Operate a dozer (wheeled and tracked) (LZ) |
OHSCER210A |
Operate a bridge and gantry crane (remote operation only) (LBG) |
60 hours |
OHSCER211A |
Operate a vehicle loading crane (less than 10 metre tonne capacity) – no occupational license applies (Statement of Attainment only) |
60 hours |
OHSCER212A |
Operate non-slewing, non-articulating mobile cranes (not exceeding three tonne capacity) – no occupational license applies (Statement of Attainment only) |
100 hours |
OHSCER215A |
Operate a roller (LR) |
40 hours |
OHSCER216A |
Operate a scraper (LP) |
OHSCER217A |
Operate a grader (LG) |
Delivery And Assessment Arrangements For
30497QLD Course in Course in Operating Cranes, Rigging and Scaffolding |
OHSCER218A |
Perform Dogging Operations (DG) * changing to CPCCLDG3001A License to Perform Dogging |
32-36 hours as a guide dependant on the experience and learning ability. |
120 hours |
4-8 hours as a guide |
OHSCER222A |
Perform Basic Rigging (RB) * changing to CPCCLRG3001A License to Perform Basic Rigging |
180 hours |
OHSCER228A |
Operate a Vehicle Loading Crane (CV) * changing to TLILIC208A License to Operate a Vehicle Loading Crane Capacity 10 Metre Tonnes and above |
60 hours |
OHSCER229A |
Operate a Bridge and Gantry Crane (CB) * changing to TLILIC308A License to Operate a Bridge and Gantry Crane |
60 hours |
OHSCER230A |
Operate a Non-Slewing Mobile Crane Greater than 3 Tonne Capacity (CN) * changing to TLILIC608A License to Operate a Non Slewing Mobile Crane Greater than 3 tonne capacity |
60 hours |
OHSCER235A |
Operate a Boom Type Elevating Workplatform greater than 11 metres (WP) * changing to TLILIC508A License to Operate a Boom Type Elevating Workplatform boom length 11 metres or more |
60 hours |
* changing to a National uniform licensing system sometime after 1 July 2010 unless assessment instruments are available before this date. All items in red are License to Perform High Risk Work (LHRW) application plus fee $70.10 (as of 1 Sep 09) to Australia Post
*LHRW (License to Perform High Risk Work) - new procedure here - application is made through Australia Post - IMPORTANT NOTE
|
